Jason Palmer, CPA, CITP

Cyber Insurance Auditing

You are here: Home / Archives for Guest Wi-Fi® Network

Securing the Home Network – Show me your MAC ID please

By Leave a Comment

Every network device has a MAC (Media Access Control) address.  This unique twelve hexadecimal digit identifier is similar to either a phone number or social security number for your network equipment.  No two should ever be identical.  This number is usually stored permanently in the device.  It is usually displayed on a label on the device in the form of: 00:23:6C:7F:38:43 or it can be displayed in the network information screen of the device.

If you want added assurance that only devices with “proper id” are allowed on to your Wi-Fi®  network, you can explicitly enter the MAC address of each of your Wi-Fi®  connected network devices in to your Wi-Fi® Router or Access Point, such as your Wi-Fi® (or Wired) Home Computers, Printers; Cell Phones, Tablets, Gaming Computers and Internet enabled devices like Blu-Ray Players and Internet enable Flat Panel TV Sets.

Even if a user has the proper SSID (Wi-Fi® Network Name) and Password, if the MAC address is not listed in the table in your Router or Access Point of “permitted MAC addresses” access will be denied and the device will not be able to connect.

The ability to configure MAC address restrictions is usually in the “Advanced Security Setup” area of your Router, Access Point, or Switch.  Almost all Wi-Fi® Routers and Access Points support MAC Address connection tables and restrictions.

Only higher end Wired Routers and Switches offering some form of Management have the MAC Address restriction capability.  Not to worry, the likelihood that someone you don’t know is directly plugging in via a “Wired” connection to your network in your home without your permission or knowledge is very small.

Technical Note:  In some cases, there are legitimate reasons why a network device would broadcast a MAC address different from the one permanently assigned.  This is called MAC Spoofing.  Some earlier Internet connection types required that the Cable or xDSL modem, the device that converts the signal from outside your home to Ethernet, be in “bridge” mode, or for all practical purposes, invisible.  In these situations, the Cable or xDSL modem would actually broadcast the MAC Address of your Computer instead of its’ own MAC Address.

Security Note:  MAC Spoofing can also be used for bad purposes and is not a fool proof security method.  It is just an added layer of security.  Even if you have a MAC Address permission table set for both your Wi-Fi® Router and any Access Points, almost anyone, with a reasonable amount of skill, can Spoof, or duplicate a legitimate MAC address which could allow them access to your Wi-Fi® network PROVIDED THAT they also know the correct SSID (network name) AND Password.  That is three layers of security instead of two.

In general, if you are extremely concerned about securing the access to your Wi-Fi® enabled network, setting the MAC Address of each Wi-Fi® enabled device in your Wi-Fi® Router and/or Access Points for your Primary (“Private”) Wi-Fi®  network will provide an added level of assurance that only legitimate, authorized devices are connecting to your network.  (For a discussion on Primary/Private vs. Secondary/Guest Wi-Fi® networks, see my article, “Securing the Home Network – Guest Wi-Fi® Networks”)

Securing the Home Network – Guest Wi-Fi® Networks

By Leave a Comment

The newest Wi-Fi® Routers support both a Primary “Private” and a Secondary “Guest” Wi-Fi® network.  This allows you to have two separate SSID’s, (the names of your Wi-Fi® networks), at the same time.  Specifically, the Primary Private Wi-Fi® network would be for your exclusive use and connect all of your Wi-Fi® or Wired Home Computers, Printers; Cell Phones, Tablets, Gaming Computers and Internet enabled devices like Blu-Ray Players and Internet enable Flat Panel TV Sets to each other and the Internet.

The Secondary Guest Wi-Fi® network would connect visiting Internet enabled devices, like Tablets, Notebook Computers, Smartphones, and Gaming Computers ONLY to the Internet.  After all, you have no idea where those Internet enabled devices have been nor can you be sure they have been practicing “Safe Computing” with proper Antivirus and Firewall software installed.

Guests are given a different SSID and password to access the alternate, dedicated Wi-Fi® “Internet Only Access” network in your home.  You may be wondering, “If it is a Guest Wi-Fi® network, why do I need to set a password at all?”  Answer:  You do not want to be providing “Free” Internet access to your neighbors and more specifically, anyone who just happens to be passing by.

If you already have a Wi-Fi® Router installed and it does not support both Primary Private and Secondary Guest networks, you have two options:  upgrade your Router or purchase an Access Point.  The advantage of purchasing a new Wi-Fi® Router that supports both Primary and a Secondary network is that most likely it will also be Dual Band.  This means that it operates at both the 2.4Ghz and 5Ghz spectrums.  (See my article on “Understanding the Wi-Fi® 802.11 Network Standard” for more details.)  The 5Ghz spectrum is less crowded and may give you better Wi-Fi® performance in your home.

If you purchase an Access Point to create a Secondary Guest Wi-Fi® network, most support the option to configure in “AP Isolation Mode.”  This means that Wi-Fi® connected devices cannot see other Wi-Fi® connected devices on the same Wi-Fi® (SSID) network but they can see all of the devices on the Wired network.   For example, with AP Isolation Mode enabled, two Wi-Fi® connected Notebook computers will not see or be able to connect to each other to share files but both would be able to see a Printer physically connected with an Ethernet (wired) cable to the Network Router.   If every device in your home is connected via Wi-Fi® to your Primary Private Wi-Fi® network, then adding an Access Point is a good solution to create a Secondary Guest Wi-Fi® network.

If you have devices in your home attached to your Primary Private Wi-Fi® Network and you also have devices connected via Ethernet (wired) cables, then you need to configure the specific physical Ethernet port that your Guest Access Point is connected to on the Local Area Network side of the Router to only connect to the Internet/Wide Area Network of the Router.  This completely isolates Guest Wi-Fi® connections through the Access Point exclusively to the Internet.  Otherwise, your Guests will be able to see any device that is connected via an Ethernet (wired) cable to your network.